Recently there has been a greater awareness among fire fighters for the need to have turnout clothing laundered regularly. The NFPA Technical Committee for structural clothing addressed this in the 1991…
revision of NFPA 1971, by adding an appendix item dedicated exclusively to the care and cleaning of bunker clothing. Simply put, clean protective clothing reduces the potential for health and safety risks. Currently, there is an NFPA user document for the Selection, Care, and Maintenance of protective clothing (NFPA 1851) with an anticipated publish date of February 2001. The Globe label on every garment provides basic information for laundering. What follows is a much more comprehensive set of instructions for cleaning gear.
GUIDELINES
- If the liners are detachable, they should be removed from the shell and laundered separately. This is to prevent any contaminants the shell may have been exposed to from being transferred to the liner system during the laundering process. This will also facilitate drying of the protective clothing, especially the liners.
- All closures should be fastened: velcro hook covering pile, hooks and dees fastened, zippers zipped and snap’s closed. It is imperative that you cover the hook portion of all velcro to prevent snagging during laundering.
- We recommend a front loading washer machine, which does not have an agitator, and preferably one that is designated specifically for cleaning turnouts. A stainless steel tub should be utilized if available.
- We suggest using a laundry bag to protect the inside of the washing machine from the hooks and dees (and to protect the hooks and dees from the agitator of a washing machine when using a top load model).
Machine Washing:
We are often asked if machine washing will affect the protective qualities of your turnout gear. The special fabrics that make up your turnouts contain inherent flame and heat resistance properties, which cannot be washed off or worn out. However, given the nature of the contaminants to which fire fighters are exposed, we recommend that you never, never, use the same machine that you do your home laundry in. When machine washing, always prepare the clothing as directed, by fastening all closure systems. Use warm water and a normal cycle. Following each complete wash cycle, thoroughly rinse your garments; we recommend a double rinse with clear water.
Protective clothing should always be washed separately in a laundry bag; do not overload the washing machine, do not use softeners, and NEVER use chlorine bleach. We do not suggest machine drying; our recommendation is to hang in a shaded area that receives good cross ventilation or hang on a line and use a fan to circulate the air. Naturally, the turnout system will dry more quickly if you separate the layers for laundering and if you turn the liner system inside out to facilitate drying of the quilt thermal barrier.
Cleansers:
Cleansers generally fall into two categories, detergents and soaps. Of the two, detergents make the best cleansers because they are formulated to contain special agents that help prevent redeposition of soil. Soil redeposition is soil which is first removed from a laundered article, but later in the same wash cycle is redeposited as a thin soil film on the entire surface of the article. The most distinctive advantage of detergents is that they do not form curd in hard water. Soap curd is the material which forms a ring around the bathtub when bathing with soaps, and this curd is extremely difficult to rinse out of your garment. All cleaning agents are clearly labeled as being either detergents or soaps; and we recommend liquid detergents, since they are less likely to leave any residue on the clothing. Examples of some of the better known detergents would be Cheer or Tide.
Spot Cleaning and Pretreating:
Precleaners can be used to clean light spots and stains on protective clothing. Squirt the precleaner onto the soiled area and gently rub fabric together until a light foam appears on the surface; this foam should be completely rinsed off with cool water prior to washing. A soft bristle brush, such as a toothbrush may be used to gently scrub the soiled area for approximately one to one and a half minutes. An alternative method would be to pretreat garment by applying liquid detergent directly from the bottle onto the soiled area and proceed as with precleaners. Any spot cleaning or pretreating should be followed by machine washing prior to field use.
Dry Cleaning:
Again, the protective qualities of your Globe turnout clothing will not be adversely affected by dry cleaning. However, dry cleaning can completely ruin both the 3M triple trim and the Reflexite trims and is therefore not recommended. If you should decide that your particular exposure requires dry cleaning, knowing and accepting the risks involved, you must be sure and specify to the launderer to use non-flammable dry cleaning processes that will not adversely affect the materials. Again, our experience is that dry cleaning will result in Reflexite trim becoming cracked and brittle.
Special Cleaning Compounds:
Since Globe is in the business of producing fire fighters’ clothing and not cleaning agents, we are not able to “endorse” any of the special compounds that are being advertised for the fire service, such as Winsol or Smoke Out. However, we would recommend that each department interested in these specific cleaning agents contact the manufacturers directly and make your own determination as to suitability. The appendix on cleaning found in the 1991 edition of NFPA 1971, includes the following examples of household products that may be utilized for normal laundering, spot treating and pretreating:
Detergents:
Liquid Cheer, Liquid Fab, Liquid Tide, Liquid Wisk
Oxygenated Bleaches:
Liquid Clorox 2, Liquid Vivid
Spot Cleaning and Pretreating:
Liquid Spray & Wash, Liquid Tide, Liquid Shout,
Liquid Dishwashing Detergent
Removing Oil or Tar:
Oil based soils such as motor oil and tar can be removed with solvents such as “Varsol” prior to washing, says E.I. DuPont, the folks who produce the Nomex fibers. However, they do add the cautionary statement that the garment must be thoroughly washed and rinsed to insure that all residual solvent is completely removed. They also point out that coated material should never be dry cleaned. Celanese, the manufacturers of the PBI fiber, also recommend in their User Advisory that solvents such as Varsol may be used to remove stubborn stains such as tar, providing that the garments are well laundered and rinsed prior to actual use. You must always avoid using solvents on the leather or reflective trim.
Bleach:
One of the most often asked questions concerns the decontamination of a turnout system, especially with chlorine bleach. UNDER NO CIRCUMSTANCES should chlorine bleach be used on fire fighters’ clothing; most systems contain Kevlar, either as a blend or as the primary fiber, and Kevlar is completely destroyed by exposure to bleach. If it is absolutely essential that a bleach be used, we recommend 1/2 cup of liquid oxygenated bleach to one cup of detergent.
Trim:
3M, the manufacturers of both Scotchlite and Triple Trim, recommend that the following guidelines be used for their product: (1) Damp wipe, using warm water and mild detergent. Rinse thoroughly, dry with a soft cloth, or allow to air dry. (2) If you choose to machine wash, use warm water. (3) Do not dry clean. The producers of Reflexite trim state that dry cleaning is not permissible under any circumstances, nor is ironing ever allowed. Their recommendation is that you use a soft rag or sponge and that denatured alcohol be used as a cleaning agent. They advise against abrasive cleaners, strong solvents, and machine drying.
Decontamination:
For extreme contamination with products of combustion, fire debris or body fluids, removal of the contaminants by flushing with water as soon as possible is necessary, followed by appropriate cleaning. In the case of blood born pathogens, recommended decontamination procedures include using a .5 to 1% concentration of Lysol, or a 3-6% concentration of stabilized hydrogen peroxide. Liquid glutaraldehyde, available through commercial sources, will also provide high to intermediate levels of disinfectant activity. Decontamination may not be possible when protective clothing is contaminated with chemical, biological or radiological agents. When decontamination is not possible, the garments should be discarded in accordance with local, State and Federal regulations. Garments that are discarded should be destroyed.
Hand Washing
For many years, Globe recommended hand washing for everyday cleaning of turnouts. Hand washing was thought to be the least abrasive method of laundering, and allowed the user to pay special attention to those areas that required it. The industry now recognizes that hand washing is generally not able to remove the ground-in soil embedded in the material fibers and usually only serves to remove surface dirt. However, in the event that you do not have access to a washing machine and must hand wash your garment, remove your liner system and lay the outer shell on a non-abrasive hard surface. Using a soft bristle scrub brush and a detergent (not soap), clean your garment by making circular motions with the brush, forming progressively larger circles until the entire surface has been washed. You must then rinse the shell, using clear water, to insure that all of the detergent has been removed. We recommend that you rinse the entire garment several times to avoid any possibility of soil detergent residue.
Outside Cleaning Assistance
One final question we are often asked is whether the gear can be or even should be cleaned by a professional. We are aware of several outside agencies who specialize in the cleaning of turnout clothing and just as Globe is the expert in the cutting and stitching of protective clothing, these facilities are the experts in cleaning. Since we have no control over any of their processes, we obviously cannot endorse or authorize any one of these services over another; however, we do believe they offer a valuable service and we encourage our customers to contact any of these outside cleaning facilities to determine if they are able to meet the fire department needs. Some possible questions to ask would be if they have ever had 3rd party training or testing, if they provide any warranties on their services, and whether they are able to give any guarantees concerning the effectiveness of their cleaning.
Conclusion
In caring for your turnout clothing, you must always remember that it features three piece layering and you must consider every single layer when deciding how to clean. We do encourage every department to keep their clothing clean and to routinely inspect and repair as needed. Clean turnout gear is lighter in weight, lasts longer, and is more visible than dirty turnout gear. Having dirt, soot, and other debris clinging to your gear represents a safety hazard.
We hope the enclosed information will be of service to you. If you should need additional assistance, or have more specific concerns, please do not hesitate to contact us.
TECHNICAL DATA
GLOBE MANUFACTURING CO.
Patricia A. Freeman, Technical Services Mgr.